Having a fire pit in your backyard can be an enjoyable and comforting experience, however, it can be disheartening when the igniter fails to spark. Sparking is an essential component to ignite a fire and when it is not working, it can be difficult to get the fire started.

This can be particularly troublesome if you have never lit a fire before. It is important to understand the causes of the lack of sparking and how to fix it. With the right knowledge and tools, it is possible to get your fire pit’s igniter working properly again, allowing you to enjoy all the benefits of having a backyard fire pit.

Fire Pit Igniter Not Sparking

A fire pit igniter not sparking can be a real hassle for anyone wanting to enjoy a nice outdoor fire. If you’ve determined that the igniter isn’t sparking, it’s important to identify the underlying cause.

Common causes of a non-sparking igniter include a defective power supply, a damaged spark plug, or a lack of gas flow. In the case of a defective power supply, the igniter may not be receiving enough electricity to generate a spark.

This could be due to a faulty outlet, a worn-out power cord, or a defective transformer. To ensure that the power supply is working correctly, it’s important to test the outlet, check the wiring, and inspect the transformer.

If the power supply is working correctly, then the next step is to check the spark plug. If the spark plug is damaged or worn out, it will need to be replaced.

If the spark plug is not receiving enough fuel, it can prevent the fire pit from igniting. To check the fuel flow, it’s a good idea to remove the spark plug and inspect it for debris or blockages.

If all of the above steps have been taken and the igniter still isn’t sparking, it’s possible that the igniter itself is malfunctioning. If this is the case, it’s best to replace the igniter with a new one.

Reasons Why a Fire Pit Igniter May Not Spark

Fire pits are a great way to enjoy a relaxing evening outdoors. However, when a fire pit igniter doesn’t spark, it can be frustrating.

Here are some of the most common reasons why a fire pit igniter may not spark and what you can do to fix it.

1. Out of Fuel: A fire pit igniter needs fuel to spark. If the fuel is low or empty, it won’t spark. Make sure to check the fuel level before attempting to spark the igniter.

2. Bad Ignition Coil: The ignition coil is part of the fire pit that produces the spark. If the coil is damaged, it won’t spark. Replacing the ignition coil is usually the best solution.

3. Dirty Igniter: Dirt and debris can prevent the fire pit igniter from sparking. Cleaning the igniter with a wire brush or damp cloth can help remove the dirt and debris and get the igniter sparking again.

4. Bad Battery: If the fire pit igniter is battery-powered, a bad battery can be a problem. Replacing the battery should fix the issue.

5. Clogged Fuel Line: If the fuel line is clogged, it will prevent the fire pit igniter from sparking. Cleaning the fuel line should help get the fire pit igniter working again

How to Test the Fire Pit Igniter?

Testing the fire pit igniter requires basic knowledge of the parts and their functions. Start by unplugging the power cord from the outlet. Then, remove the igniter’s mounting screws and lift it off the burner frame. Inspect the igniter electrode for soot or other debris.

If found, clean it with a soft cloth and rubbing alcohol. Check the wires for signs of wear or damage. If they appear in good condition, use a multimeter to check the resistance of the igniter.

If it is not within the manufacturer’s recommended reading, replace the igniter.

Next, reconnect the igniter and plug the power cord back into the outlet. Turn the control knob to the “on” position and press the igniter button. The electrode should spark and ignite the gas. If no spark is produced, check the igniter module and wiring for any loose connections or damage.

Inspect the flame for any signs of yellowing or flickering. If present, the igniter may need to be adjusted. Turn the control knob to the “off” position and adjust the electrode position to create a blue flame. Test the igniter again to ensure it’s working correctly.

Troubleshooting a Gas Fire Pit Igniter Not Working

To start with, check the source of the gas supply and make sure it is turned on properly. If the source is on, check the igniter, which is typically a button or switch. If it is not functioning properly, replace it with a new one.

If the gas flow is normal, check the pilot light to see if it has gone out. If it has, relight it and make sure it stays lit.

Next, check the spark plug and make sure it is clean and working properly. If it is not, replace it.

Inspect the spark gap and clean any debris that may be causing it to not work properly. Lastly, inspect the gas control knob and make sure it is set to the correct position. After all these checks, if the igniter is still not functioning, contact a professional for further assistance.

Fire Table Igniter Not Working

Tips for Fixing a Fire Table Igniter Not Working

Check Battery: The first thing to do is to check the battery and replace it if necessary. Make sure the battery is inserted correctly, and that there is sufficient voltage.

Clean Igniter: Make sure to clean the igniter with a soft cloth, as dirt and debris can prevent the igniter from working efficiently.

Check Wiring: Make sure to check that all the wires are properly connected and that there is no damage or corrosion to the wiring.

Check Gas Supply: If the fire table is connected to a gas line, make sure that the gas is turned on and that the line is free of any obstructions.

Adjust the Flame Height: If the flame is too low or too high, adjust the flame height using the valve located on the side of the fire table.

Replace Spark Generator: If the fire table is not igniting, then it may be necessary to replace the spark generator.

Common Solutions for Fire Pit Igniters Not Clicking

1. Replace Spark Generator: The spark generator may be faulty, so replacing it should solve the issue.

2. Check Fuel Valve: Check the fuel valve to make sure it is open.

3. Clean Burner Ports: Clogged burner ports will prevent ignition. Use a wire brush to clean them.

4. Check Battery: If the spark generator has a battery, check it is still functional.

5. Check Igniter Wires: Make sure the wires between the spark generator and the burner are securely connected.

6. Check Pilot Light: A pilot light that is not lit will prevent the burner from igniting.

7. Reset Control Module: If the control module is not functioning properly, reset it.

8. Check Gas Supply: Low gas pressure will prevent the fire pit from igniting.


Well, it’s been a long journey, but we’ve finally come to the conclusion that a fire pit igniter not sparking is likely due to a weak battery, a bad spark generator, or a lack of fuel. We hope that this article has helped you to understand the process of troubleshooting these issues and that you now have a better understanding of how to get your fire pit up and running again. So don’t be afraid to spark it up, and enjoy your outdoor fire pit experience!